ASTM A487 PDF
ASTM A, Martensitic, Normalized and tempered; Quenched and tempered. See the chemical composition and physical properties of ASTM A Grade CA6NM-A, find alternative materials, and connect with suppliers. See the chemical composition and physical properties of ASTM A Grade 4-A, find alternative materials, and connect with suppliers.
|Published (Last):||5 March 2005|
|PDF File Size:||13.17 Mb|
|ePub File Size:||5.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Combining values from the two systems may result in nonconformance with the specication.
ASTM A487 Grade 4-A
ASTM does not give any a87 express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Current edition approved Dec. Recording-type pyrometers shall be used to control the furnace temperature. Link to Active This link will always route to the current Active version of the standard.
ASTM A487 Grade CA6NM-A
This specification covers low-alloy steel and martensitic stainless steels in the normalized and tempered, asrm quenched and tempered conditions, suitable for pressure-containing parts. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Magnetic Particle Inspection S5.
Other surface discontinuities shall meet the visual asrm standards specied in the order. Subscribe to Premium Services Searches: Combining values from the two systems may result in non-conformance with the standard. The contents, results, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.
Within the text, the SI units are shown in brackets.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. Click here to view all the property values for this datasheet as they were originally entered into MatWeb.
Re—examination of the weld repair by radiography when Supplementary Requirement S 5 has been awtm will not be necessary when an applicable surface inspection method was used to locate the discontinuity except for the following: Repair By Welding 9. Those which are ordinarily considered suitable for use with this specication are given below. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
The values stated in each system are not exact equivalents; therefore, a47 system must be used independently of the other. Repair by welding may be done. Your comments are invited either for revision of this standard or for additional standards zstm should be addressed to ASTM Headquarters. Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtained.
Product analysis tolerances for stainless grades are not presently applicable pending development a4487 these limits. Product analysis tolerance is specified. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Other higher specied minimum average and single values may be used upon agreement between the manufacturer and the purchaser. This abstract is a s487 summary of the referenced standard.
Examination of Weld Preparation S Please contact us at webmaster matweb. The weldability of the classes in this specication varies from readily weldable to weldable only with adequate precautions, and the weldability of each class should be considered prior to assembly by fusion welding.
Originally published as A — 63T. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, vanadium, boron, and copper. The intermediate and nal PWHT temperatures shall be the same as the intermediate and nal tempering temperatures, respectively, as the original heat treatment of the castings. Data sheets for overmetals, plastics, ceramics, and composites.
ASTM A AM for Steel Castings made by Steel Foundry in China
MatWeb is intended for personal, non-commercial aastm. Martensitic, Normalized and tempered; Quenched and tempered Key Words: Questions or comments about MatWeb? All castings shall receive the specified heat treatment requirement: To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below.
Charpy Impact Test S8. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Or if you don’t have an account with us yet, then click here to register. Preliminary heat treatment and multiple tempering are permitted. The weldability of the classes in this specification varies from readily weldable to weldable only with adequate precautions, and the weldability of each class should be considered prior to assembly by fusion welding.
Historical Version s – view previous versions of standard. Unacceptable visual surface discontinuities shall be removed and their removal veried by visual examination of the resultant cavities.
Other temperatures may be used upon agreement between the manufacturer and the purchaser, in which case S 8.