ASTM C128 PDF

Referenced Documents. ASTM Standards: C 29/C 29M Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate2. C 70 Test Method for Surface. ASTM Designation: C 1. SCOPE. This method covers the determination of bulk and apparent specific gravity, 23/23ºC. (/ºF), and absorption. Qty. Model, Description. 1, Choose One: HBA, Adam Core balance g x g, V 60Hz. HBA.4F, Adam Core balance g x g, V 50/.

Author: Diramar Akinozil
Country: Paraguay
Language: English (Spanish)
Genre: Finance
Published (Last): 12 September 2009
Pages: 20
PDF File Size: 12.97 Mb
ePub File Size: 12.55 Mb
ISBN: 162-2-91036-749-2
Downloads: 59742
Price: Free* [*Free Regsitration Required]
Uploader: Faegal

Link to Active This link will always route to the current Active version of the standard.

Active Risk Management

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Alternatively, the relative density specific gravity OD is used for computations when the aggregate is dry or assumed to be dry.

This value is not widely used in construction aggregate technology. Work Item s – proposed revisions of this standard.

The OD relative density is determined after drying the aggregate. Work Item s – proposed revisions of this standard. The values obtained astmm absorption by other test methods will be different than the values obtained by the prescribed h soak, as will the relative density specific gravity SSD.

Active view current version of standard. Relative density specific gravity SSD is used in the determination of surface moisture on fine aggregate by displacement of water in Test Method C Likewise, relative density specific gravitya dimensionless quality, is expressed d128 OD, SSD, or as apparent relative density apparent specific gravity. The test results for density shall be reported in either SI units astmm inch-pound units, as appropriate for the use to be made of the results.

  ALUMIL M11500 PDF

These notes and footnotes excluding those in tables and figures shall not be considered as requirements of this test method. For an aggregate that has been in contact with x128 and that has free moisture on the particle surfaces, the percentage of free moisture is determined by deducting the absorption from the total moisture content determined by Test Method C by drying.

wstm The laboratory standard for absorption is that obtained after submerging dry aggregate for a prescribed period of time. Relative density specific gravity SSD is used if the aggregate is in a saturated surface-dry condition, that is, if its absorption has been satisfied.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The SSD density, SSD relative density, and absorption are determined after soaking the aggregate in water for a prescribed duration. Historical Version s – view previous versions of standard. These notes and footnotes excluding those in tables and figures shall not be considered astn requirements of this test method. It is also expressed as the ratio of the density of the aggregate particles to the density of water.

  74HC123N DATASHEET PDF

The relative density specific gravitya dimensionless quality, is expressed as oven-dry ODsaturated-surface-dry SSDor as apparent relative density specific gravity.

ASTM C Standard

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Aggregates mined from below the water table commonly have a moisture content greater than the absorption determined by this test method, if used without opportunity to dry prior to use. Conversely, some aggregates that have not been continuously maintained in a moist condition until used are likely to contain an amount of absorbed moisture less than the h soaked condition.

No other units of measurement are included in this standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The OD density and OD relative density are determined after drying the aggregate. Satm SSD relative density and absorption are determined after soaking the aggregate in water for a prescribed duration. Link to Active This link will always route to the current Active version of the standard.