ASTM G32 PDF

CAVITATION EROSION TESTING (ASTM G). SONICS & MATERIALS, INC. Because evaluation of cavitation erosion resistance can be facilitated using. Controllable and reproducible ultrasonication is needed to perform cavitation erosion testing in accordance with ASTM Standard G Hielscher ultrasonic . ASTM G32 Vibratory Captivation Erosion Test Buttons are available in Note: Metal Samples manufactures test apparatus in accordance with ASTM standards.

Author: Fenrizilkree Gardaramar
Country: United Arab Emirates
Language: English (Spanish)
Genre: Life
Published (Last): 9 August 2012
Pages: 67
PDF File Size: 17.86 Mb
ePub File Size: 11.15 Mb
ISBN: 349-8-99779-931-6
Downloads: 58625
Price: Free* [*Free Regsitration Required]
Uploader: Shakazragore

It also specifies standard reference materials that must be used to verify the operation of the facility and to define the normalized erosion resistance of other test materials.

This is because the compliance of the coating on the specimen may reduce the severity of the liquid cavitation induced by its vibratory motion.

ASTM G32 – 16 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus

Test Method G73 describes another testing approach v32 intended for that type of environment. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The method therefore offers a small-scale, relatively simple and controllable test that can be used to compare the cavitation erosion resistance of different materials, to study in detail the nature and progress of damage in a given material, or — by varying some of the test conditions — to study the effect of test variables on the damage produced.

The stationary specimen approach can also be used for brittle materials which can not be formed aetm a threaded specimen nor into a disc that can be cemented to a threaded specimen, as required for this test method see 7.

The latter may be more suitable for materials not readily formed into a precisely shaped aatm. This must be considered in planning, conducting and reporting a test program. An alternative method for similar purposes ashm Test Method Gwhich employs a cavitating liquid jet to produce erosion on a stationary specimen.

  EUROTHERM 818P PDF

It also specifies standard reference materials that must be used to verify the operation of the facility and to define the normalized erosion resistance of other test materials.

The inch-pound units given in parentheses are for information only. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It permits deviations from some of these conditions if properly documented, that may be appropriate for some purposes. Link to Active This link will always route to the current Active version of the standard.

However, adaptations of the basic method and apparatus have been used for such purposes see 9. Link to Active This link will always route to the current Active version of the standard. Small differences between two materials are probably not significant, and their relative ranking could well be reversed in another test.

It permits deviations from some of these conditions if properly documented, that h32 be appropriate for some purposes. Referenced Documents purchase separately The documents listed below are astn within the subject standard but are not provided as part of the standard. The results of either, or anycavitation erosion test should be used with caution; see 5.

It gives guidance on setting up a suitable apparatus and covers asfm and reporting procedures and precautions to be taken. The result would not be representative of a field application, where the hydrodynamic generation of cavitation is independent of the coating.

The vibration induces the formation and collapse of cavities in the liquid, and the collapsing cavities produce the damage to and erosion material loss of the specimen.

The inch-pound units given in parentheses are for information only. For specific safety warning information, see 6. The vibration induces the formation and collapse of cavities in the liquid, and the collapsing cavities produce the damage to and erosion material loss of the specimen.

  IEC 61892-2 PDF

ASTM G32 Captivation Erosion Test Button

While g23 investigators have used this approach see X4. For this reason, the consistency of results between different test methods or under different field conditions is not very good.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. However, adherence y32 this test method in all other respects will permit a better understanding and correlation between the results of different investigators.

For specific safety warning information, see 6. It gives guidance on setting up a suitable apparatus and covers test g322 reporting procedures and precautions to be taken. Historical Version s – view previous versions of standard.

The method therefore offers a small-scale, relatively simple and controllable test that can be used to astmm the cavitation erosion resistance of different materials, to study in detail the nature and progress of damage in a given material, or—by varying some of the test conditions—to study the effect of test variables on the damage produced. In that method, the specimen is fixed within the liquid container, and the vibrating tip of the horn is placed in close proximity to it.

V32 view current version of standard. Guide G may be followed in order to determine the synergism between the mechanical and electrochemical effects.