BEARCAT BCT15X MANUAL PDF
The Uniden Bearcat BCT15X is the follow-up to Uniden’s premier analog mobile scanner, the manual for the radio is contained on a CD-ROM, in PDF format. DImage_/Manual/ (1 of 3)5/26/ .. This page applies to the following scanner(s): BCDXT BCT15X Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. View and Download Uniden BCT15 owner’s manual online. scanner radio with You can adjust the level of the following tones: Key Beep, BearTracker Alert.
|Country:||Antigua & Barbuda|
|Published (Last):||15 November 2013|
|PDF File Size:||10.13 Mb|
|ePub File Size:||6.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Unlocked — the group is scanned.
Scroll to Auto56. If the frequency has already been stored, the mznual continues to search. The Bear Tracker Warning System monitors these frequencies used bezrcat mobile extender radios as well as car-to-car, aircraft-to-car, and other special-purpose frequencies. When you use startup configuration, the scanner checks all systems, sites, and search ranges and: Alert Only – the scanner immediately sounds a weather alert siren when it detects the Hz weather alert tone, then opens the squelch and remains on the weather channel.
Band Scope Mode- the mode the radio is in while doing a Band Scope search. Press then VOL State.
Press  to toggle Close Call mode. If you don’t have Excel you can download and install a viewer here. Simplex systems use a single frequency for both transmit and receive.
You will see activity in the bearcst bands in the display.
UNIDEN BCT15 OWNER’S MANUAL Pdf Download.
To select a different channel, turn the Scroll Control. Mnaual to toggle the lockout status of a channel in Scan Mode. Set Delay Time Sets the number of seconds the scanner should wait after a transmission stops before moving on to the next channel during weather scan.
Press then to toggle group quick keys on or off in Scan Mode. To check for a repeater frequency press Hold to hold on the frequency. You can set the center frequency and span of the frequency range. Therefore, if your fire department dispatch talk group isand they do dispatch tone-outs and alarms as Multi-selects, then those communications will be on talk group To change search direction or continue searching turn the scroll control back or forward.
All trunked systems need at least one site to enter trunking frequencies.
The default setting is off. Scroll to the desired delay time-5, -2, 0, 1, 2, 5, 10, or 30 secs. Bfarcat 7 Setting I-Call Operation Typical repeater systems provide coverage out to about a mile radius from the repeater location.
Top Questions for Uniden BCT15X Scanner
Auto — The scanner uses the default modulation for the frequency band. You can set the scanner so the Close Call feature checks for a Close Call hit every 2 seconds in the background while you are scanning or searching or use Close Call only mode. Programming A Same Group This setting determines which types of signals will trigger an alert.
Radio Reference has a good webpage here: Start Of Transfer 3b. The default setting is Yes. To go to a channel number tag in a different system Hold on any channel.
For example, the display to set the modulation looks like: This is a special system that automatically stores the last 10 close call hits and allows you to scan them. Tone-Out Search Mode is used if you don’t know the tones. Enter any 3-digit system number tag then.
You can enter a wildcard that matches all I-calls by programming [. Since the trunking system might send a call and its response on different frequencies, it is difficult to listen to trunked communications using a conventional scanner. Priority ID Scan is always on for a system if enabled in the system setting. Private Systems – lets you flag a system so that it cannot be read out of the scanner or modified only with optional software.
To cancel a CC hit turn the scroll control. The following geographical values are typical of use you might find valuable while traveling.
Level 1 – 15 — the scanner lets you manually select one of fifteen key bct15xx levels. Press MENU twice to return. To toggle the volume offset for a channel Hold on the channel and press then 5 LVL. The maps that are Hybrid systems are in bold. VHF Low 1 — Scroll to ‘ Disp.