DIN EN 10243-1 PDF

Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS. Standard DIN EN Steel die forgings – Tolerances on dimensions – Part 1: Drop and vertical press forgings; German version EN.

Author: JoJozilkree Meztisida
Country: Bulgaria
Language: English (Spanish)
Genre: Automotive
Published (Last): 5 March 2012
Pages: 413
PDF File Size: 3.95 Mb
ePub File Size: 14.91 Mb
ISBN: 287-8-12026-689-4
Downloads: 77914
Price: Free* [*Free Regsitration Required]
Uploader: Sak

A similar procedure is followed for the factor of shape complexity so that downward displacement of the horizontal line used is nil, one place, two places and three places for factors S1, S2, S3 and S4 respectively.

These normative references are cited at the appropriate places in the text and the publications are listed hereafter. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the English versionSteel die forgings Tolerances on dimensions Part 1: Base all thickness tolerances except those for overall thickness on dimension t shown above.

The centre-to-centre tolerances provided in this standard apply only when a straight line joining the two centres occurs within the profile of the forging see Figure Where more restrictive tolerances are required for application to individual dimensions of thickness, supplementary operations are involved. In the case of a forging having a flange from which projects: The shape complexity factor of a forging is the ratio of the mass of the forging to the mass1 of the enveloping xin necessary to accommodate the maximum dimensions of the forging: The tolerances are determined from Table 3 and Table 4 in accordance with the greatest thickness dimension of the forging.

Users are responsible for its correct application. In those di where the variation is of importance e. In measuring mismatch, accuracy depends upon making due allowance for surplus metal caused by uneven die wear.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. Normally the tolerances for the greatest dimension of length or diameter of the forging 102243-1 be applied but, if more restrictive tolerances are required, those for the specific dimension of the pierced hole may be used.

  FUNZIONI MONOTONE PDF

DIN EN 10243-1

The tables showing dimensional tolerances are based on the R20 series of preferred numbers see ISO 3. As a rin rule grade F tolerances result in a cheaper forged component. Permissible tolerances based on the greatest dimensions are usually obtained from dih appropriate table Maximum length: They are classified into four groups; accordingly each of them is displayed in the table.

Lou Pingeot Dangerous Partnership – Sie? Also, the deviations of form do not include scale pits and depth fn surface dressing see 5. The cost of the forged part can be higher if grade E tolerances are selected, but the need for subsequent machining operations can often be reduced.

The supplier will draw the attention of the purchaser to such instances and it will be necessary to negotiate greater tolerances on the draft angle surfaces to meet these circumstances.

When no tolerance is indicated against the dimension concerned, the tolerance for the maximum length or width of the forging shall be applied from Table 1 or Table 2but the dispersion will be plus and minus one-half of the total tolerance, and not as shown 102431- the tables.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Marchand conflicting national standards shall be withdrawn at the latest by March ej These marks may be either sunken or raised. Above 0,32 up to and including 0,63; S1: The minus tolerances do not apply to edge radii up to and sin 3 mm when such radii are affected by subsequent removal of draft by trimming or punching. In extreme cases they can cover the whole field of tolerances unless otherwise agreed between the supplier and the purchaser.

  CIANOSIS CENTRAL Y PERIFERICA PDF

VanDeusen Wisc B Documents.

EN 10243-1.pdf

Up to and including 0,16;S3: The location of burrs shall be indicated to the purchaser on the forging drawing for approval before the commencement of production.

Ost 1 71 english translation deutsch, francais, italiano Business. All variations, including those due to die wear and shrinkage, are included in the length, width and height tolerances. The positive residual flash and negative trimmed flash values permitted are given in Table 1 and Table 2. This publication does not purport to include all the necessary provisions of a contract. Mismatch tolerances depend on the forging mass ne on the shape of die line.

Many instances of heavy die wear occur in which these tolerances are inadequate. This grade should not be specified unless the additional forging cost entailed can be justified by 12043-1 consequent saving in overall cost. This should be done to obviate unnecessary minor variations between tolerances, thus facilitating drawing preparation and simplifying inspection procedures.

DIN EN – Free Download PDF

This European Standard does not apply to upset forgings made on horizontal forging machines see EN The height or the depth of an ejector mark, relative to the surrounding surface, shall not exceed one-half Figure 13 Application of thickness tolerances to deep hubs14 BSI 12 January of the total tolerance permitted, unless stated otherwise on the agreed forging drawing.

Straightness and flatness tolerances are applied independently of, and in addition to, any other tolerances. They are best dealt with by consultation at the design stage and shall be agreed between the purchaser and the supplier. Reference dimensions included in the 10243–1 are given in brackets.

This special procedure is not applied if larger tolerances will result from use of the normal procedure as shown in 4.