EN25FQCP 8 Mbit Serial Flash Memory with 4kbytes Uniform Sector. 8 Mbit Serial Flash Details, datasheet, quote on part number: EN25FQCP . EN25F80 Datasheet PDF Download – 8 Mbit Serial Flash Memory, EN25F80 data sheet. Eon EN25F80 datasheet, 8 Mbit Serial Flash Memory (1-page), EN25F80 datasheet, EN25F80 pdf, EN25F80 datasheet pdf, EN25F80 pinouts.

Author: Dugis Zulkiran
Country: Cuba
Language: English (Spanish)
Genre: Technology
Published (Last): 24 December 2015
Pages: 329
PDF File Size: 13.77 Mb
ePub File Size: 20.25 Mb
ISBN: 529-1-13575-171-9
Downloads: 80901
Price: Free* [*Free Regsitration Required]
Uploader: Kigajinn

The device then en225f80 into the Stand-by Power mode. To spread this overhead, the Page Program PP instruction allows up to bytes to be programmed at.

Full text of “Datasheet: EN25F80”

After successful write cycle, the state of the Write in Progress Datashert bit is set to 0 automatically, and the device is ready to accept another erase or write instruction. Product successfully added to your shopping cart. I have verified my wiring. Host MCU can retrieve the operating characteristics, structure and vendor specified information such as identifying information, memory size, operating voltage and timing information of this device by sending the SFDP Read command 0x5Afollowed by 3 bytes of address and one dummy byte.

EN25F80 Datasheet

This Data Sheet may be revised by subsequent versions 1 or modifications due to changes in technical specifications. The device is first selected by driving Chip Select Low. Recommended Operating Ranges define those limits between which the functionality of the device is guaranteed. Chip Select CS can be driven High at any time during data output.


EN25F80 Hoja de datos ( Datasheet PDF ) – 8 Mbit Serial Flash Memory

The full application code, and ready to use libraries can be found on our Libstock page. I think SS on the Mega is 50, but confirm that. They define the size of the area to be software protected against Program and Erase instructions.

This product is no longer in stock. Chip Select CS must be driven High after the eighth bit of the instruction code has been latched in, otherwise the Chip Erase instruction is not executed. Chip Select CS can be driven High after any bit of the data-out sequence is being en25c80 out.

Dqtasheet can also be used as an extra software protection mechanism, while the device is not in active use, since in this mode, the device ignores all Write, Program and Erase instructions.

Other mikroE Libraries used in the example: When CS is brought low the device will be selected, power consumption will increase to active levels and instructions can be written to and data read from the device. You can tell the results are gibberish because the status register byte should stay constant.

The used Flash module has very good endurance and it can withstand up towrite cycles, with the data retention period of about 20 years. This is followed by the internal Program cycle of duration tPP. This is followed by the dataheet device identification, stored in the memory, being shifted out on Serial Data Outputeach bit being shifted out during the falling edge of Serial Clock.


Doing this will ensure compatibility with future devices. The Write In Progress WIP bit is provided in the Status Register so that the application program can monitor its value, polling it to establish when the previous Write cycle, Program cycle or Erase cycle is complete.

The provided click library is mikroSDK standard compliant. Datwsheet made code that reads the addresses and status register and prints them via serial. When set to 1, such a cycle is in progress, when reset to 0 no such.

EN25F80 Datasheet PDF

Page Programming To program one data byte, two instructions are required: Status register bit locations 5 and 6 are reserved for future use. The primary difference between Mode 0 and Mode 3, as shown in Figure.

Before this can be applied, the. CS is High, the device is disabled, but could remain in the Active Power mode until all internal cycles. All attempts to access the memory array during a Write Status Register cycle, Program cycle or Erase cycle are ignored, and the internal Write Status Register cycle, Program cycle or Erase cycle continues unaffected.

There are bytes of OTP memory, which can be used to store various security data. Register, Program or Erase cycle.