GIGRAC 600 MANUAL PDF
Information in this manual is subject to change without notice and does . Firstly we’d like to thank you for choosing the Soundcraft GigRac st. We hope you have .. The Mid Control is set at Hz and allows you to either add or remove. Available in two models (GigRac and the stereo GigRac st),. GigRac combines a fully-featured 8 channel mixer with studio-quality digital effects. Instructions in the User Manual before using your mixer for the first time. © Harman International RACK BOLT-GIGRAC GR// P-SN
|Published (Last):||20 February 2015|
|PDF File Size:||14.98 Mb|
|ePub File Size:||18.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Don’t show me this message again. Answered on Aug 19, The manuaal then shuts down. It is acceptable for this LED to come on momentarily every now and then but the Main or Monitor Master Volume depending on which mode has been selected: You should also be able to see activity on the Output Meter 4 Note: This is very important to prevent any damage to either the GigRac or your loudspeakers!
SoundCraft GigRac manuals
Please assign your manual to a product: Soundcraft is a trading division of Harman International Industries Ltd. This warranty shall only be valid if: IT requires special diagnostic tools and troubleshooting as gigdac as soldering ability. If the mains fuse fails repeatedly this may be because an electrical safety hazard exists.
As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Answered on May 04, Using good quality speaker cables connect the loudspeakers to the Speaker outputs on the rear of the GigRac.
Posted on May 10, Be the first to answer. Posted on Aug 07, Be the first to answer. Cannot turn the Check the fuse. Answered on Apr 07, Plugging in an Acoustic Guitar, Stereo Keyboard or CD Player The GigRac will happily receive signals from instruments with either mono or stereo outputs such as guitars Mono or stereo keyboards and CD Players Stereo Before plugging in, make sure the Main Volume control 2 for the chosen channel is turned fully off to avoid accidental damage to your speakers.
Posted on Jan 16, Be the first to answer.
Soundcraft GIGRAC User Manual
Posted on Jun 14, Be the first to answer. Page 11 Turn the Main Master Volume control 1 up to about half-way.
Most Popular Question need purchase Music. Answered on Feb 23, Answered on Jan 16, You seem to have answered your own question but it is possible that the speaker jack is defective. Posted on Giigrac 23, Be the first to answer. To print the manual completely, please, download it. Recent Popular Answered Unanswered.
20 Most Recent Soundcraft Gigrac Powered Mixer Questions & Answers – Fixya
The XLR input on channels 1 – 4 is very sensitive. One needs to use test equipment to measure the current through the resistor and see if it is reasonable. Page 13 Plugging in an Acoustic Guitar, Stereo Keyboard or CD Player The GigRac will happily receive signals from instruments with either mono or stereo outputs such as guitars Mono or stereo keyboards and CD Players Stereo Before plugging in, make sure the Main Volume control 2 for the chosen channel is turned fully off ,anual avoid accidental damage to your speakers.
Additional damage often occurs when users replace fuses that have blown due to internal failures in equipment.
By pressing ‘print’ button you will print only current page. Channels are designed to handle mono microphone or mono line level signals only. Your unit is telling you that there is something wrong. Posted on Sep 03, Be the first to answer. Connecting up your loudspeakers to the GigRac Note: Are you a Soundcraft Music Expert?
This should get gjgrac a fair way in to finding the fault. If it does than re-connect one amp at the time and see what happens.
My guess, for what it’s worth, is one of the mznual has a bad final so I would 60 the power supply from the amps and see if the unit keeps running. Page 10 Connecting up your loudspeakers to the GigRac Note: Posted on Aug 31, Be the first to answer.
You should now hear the microphone signal appearing in the loudspeakers as you begin to speak. This can be in two places, your power supply is shutting down thermal because of a component fault, and or your Amp gigarc are overheating due to also a component fault.
We hope you have many happy years together! Enter text from picture: Table of Contents Add to my manuals Add. Unfortunately there is no audio input on most laptops so you need another solution. Soundcraft Music Answered on Nov 09,